在线客服
企业微信
点击图片查看原图
SIF-400
[特点]
·PLC和温度控制器DCL-33A或JC□-33A连接专用单元
[特点]
·PLC和温度控制器DCL-33A或JC□-33A连接专用单元
IF-400 新款 IF-600 通信变换器
本器は，ホストコンピュータまたはPLC(RS-232CまたはRS-422)と調節計(シリアル通信機能RS-485 [オプション: C5])との通信を仲介する通信変換器です。 弊社標準プロトコルおよびModbusプロトコルに対応しています。 また，調節計側通信ラインに本器を接続すると，リピータとして使用できます。 リピータが 31 台目の接続機器となり，リピータの調節計側にさらに*大 31 台の調節計を接続できます。 リピータは*大 3 台接続でき，調節計のアドレス数制限 95 台まで接続できます。
本器をリピータとして使用すると，調節計を32台以上接続できます。
また，通信ラインを1.2km以上延長できます。
リピータは*大3台，調節計はアドレス数制限95台まで接続できます。(通信ラインは*大4.8km)
本器は，ホストコンピュータまたはPLC(RS-232CまたはRS-422)と調節計(シリアル通信機能RS-485 [オプション: C5])との通信を仲介する通信変換器です。 弊社標準プロトコルおよびModbusプロトコルに対応しています。 また，調節計側通信ラインに本器を接続すると，リピータとして使用できます。 リピータが 31 台目の接続機器となり，リピータの調節計側にさらに*大 31 台の調節計を接続できます。 リピータは*大 3 台接続でき，調節計のアドレス数制限 95 台まで接続できます。
本器をリピータとして使用すると，調節計を32台以上接続できます。
また，通信ラインを1.2km以上延長できます。
リピータは*大3台，調節計はアドレス数制限95台まで接続できます。(通信ラインは*大4.8km)
[特点]
·一个在控制器（RS-485）与主机（RS-232C或RS-422A）之间的通信转送/转换器
串行通信 主机与IF400间：RS-232C/RS-422A/RS-485标准
通信速度 通信速度可以通过增加或减少键来选择2400,4800,9600,19200BT 按MODE键确认
（IF-400)-(温度调节仪间通讯）
串行通信 RS-485标准
电源电压 100-240V AC 50/60HZ
安装方式 轨道安装式轨道
外形尺寸 22.5（W)*75(H)*100(D)MM
·一个在控制器（RS-485）与主机（RS-232C或RS-422A）之间的通信转送/转换器
串行通信 主机与IF400间：RS-232C/RS-422A/RS-485标准
通信速度 通信速度可以通过增加或减少键来选择2400,4800,9600,19200BT 按MODE键确认
（IF-400)-(温度调节仪间通讯）
串行通信 RS-485标准
电源电压 100-240V AC 50/60HZ
安装方式 轨道安装式轨道
外形尺寸 22.5（W)*75(H)*100(D)MM
Preface
Thank you for purchasing our SIF-600, PLC interface unit.
This manual contains instructions for the mounting, functions, operations and notes when operating the
SIF-600. To ensure safe and correct use, thoroughly read and understand this manual before using this
instrument. To prevent accidents arising from the misuse of this instrument, please ensure the operator
receives this manual.
Notes
This instrument should be used in accordance with the specifications described in the manual.
If it is not used according to the specifications, it may malfunction or cause a fire.
Be sure to follow all of the warnings, cautions and notices. If they are not observed, serious injury or
malfunction may occur.
The contents of this instruction manual are subject to change without notice.
Care has been taken to assure that the contents of this instruction manual are correct, but if there are any
doubts, mistakes or questions, please inform our sales department.
This instrument is designed to be installed on a DIN rail within a control panel. If it is not, measures must be
taken to ensure that the operator cannot touch power terminals or other high voltage sections.
Any unauthorized transfer or copying of this document, in part or in whole, is prohibited.
Shinko Technos CO., LTD. is not liable for any damage or secondary damage(s) incurred as a result of using
this product, including any indirect damage.
Safety Precautions (Be sure to read these precautions before using our products.)
The safety precautions are classified into 2 categories: “Warning” and “Caution”.
Depending on the circumstances, procedures indicated by Caution may cause serious results, so be sure
to follow the directions for usage.
Warning
Procedures which may lead to dangerous conditions and cause death or serious injury, if not carried
out properly.
Procedures which may lead to dangerous conditions and cause superficial to medium injury or physical
damage or may degrade or damage the product, if not carried out properly.
Thank you for purchasing our SIF-600, PLC interface unit.
This manual contains instructions for the mounting, functions, operations and notes when operating the
SIF-600. To ensure safe and correct use, thoroughly read and understand this manual before using this
instrument. To prevent accidents arising from the misuse of this instrument, please ensure the operator
receives this manual.
Notes
This instrument should be used in accordance with the specifications described in the manual.
If it is not used according to the specifications, it may malfunction or cause a fire.
Be sure to follow all of the warnings, cautions and notices. If they are not observed, serious injury or
malfunction may occur.
The contents of this instruction manual are subject to change without notice.
Care has been taken to assure that the contents of this instruction manual are correct, but if there are any
doubts, mistakes or questions, please inform our sales department.
This instrument is designed to be installed on a DIN rail within a control panel. If it is not, measures must be
taken to ensure that the operator cannot touch power terminals or other high voltage sections.
Any unauthorized transfer or copying of this document, in part or in whole, is prohibited.
Shinko Technos CO., LTD. is not liable for any damage or secondary damage(s) incurred as a result of using
this product, including any indirect damage.
Safety Precautions (Be sure to read these precautions before using our products.)
The safety precautions are classified into 2 categories: “Warning” and “Caution”.
Depending on the circumstances, procedures indicated by Caution may cause serious results, so be sure
to follow the directions for usage.
Warning
Procedures which may lead to dangerous conditions and cause death or serious injury, if not carried
out properly.
Procedures which may lead to dangerous conditions and cause superficial to medium injury or physical
damage or may degrade or damage the product, if not carried out properly.
